Compool Cp3800 User's Guide download pdf (Page 12)

Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide

Controls and buttons (Continued)

Menu/back button: Use this button to access, save and exit from a current menu or sub-menu

settings. Also, while in a menu or sub-menu items, use this button to go back to a previous menu

level or item. If no menu activity is detected after five minutes, the main screen is displayed. All

menu settings are permanently saved and retained in the control panel even after power is removed

from the control panel. Control panel buttons are disabled while in the menu mode.

Right button/SELECT: When in pool or spa mode use the Left and Right button to adjust the

temperature level. Press the Right button to raise the set point water temperature. Press the Filter

Pump (F) button to display the current water temperature. Use the Right button to select a sub-menu

item for editing. After pressing the Menu button to access the main menu items, use the Right button

to select the menu item and access the sub-menu items for adjustment. While editing a settings,

press and hold the Right button to fast forward through settings and values.

Filter Pump (F) button/LED: Switches a single speed filter pump on and off in “Pool” or “Spa”

mode. Press the Valves (V) button to toggle between “Pool” and “Spa” mode and rotate valves. If

“Heater” is enabled in the “Heat” menu (see page 25), pressing the Filter Pump button will also

enable the selected heat source (Heater/Solar LED on). The default time before the filter pump will

switch off is 12 hours. This button operates in “Auto” or “Service” mode.

Single-Speed Filter Pump: If the pump is currently off, press the Filter Pump button (LED on) to

switch the pump on. Press the Filter Pump button again to switch the pump off. However, if the

heater is operating, and a delay is enabled for valves, this allows the heater to cool down (heater

cool-down), then when you press the F button to switch off the pump, only the heater will turn off,

then the filter pump will automatically switch off after 10 minutes to allow the heater to cool down.

Pentair Water Pool and Spa

heaters do not require a cool down time. To override the “heater cool-

down,” press the Filter Pump button again to switch off the pump.

Two-Speed Filter Pump: Press the Filter Pump button (LED on) to switch the two-speed pump on

in high speed. If you switch the pump off to low speed shortly after switching it to high speed, the

filter pump will automatically remain in high speed for a few minutes before switching back to low

speed to allow the pump to prime and establish normal water flow. In order to use the “2-Speed

Pump” menu assignments (see page 42), the 2-Speed relay option must be installed in the

EasyTouch Load Center.

Freeze Protection: This function protects the pool, plumbing, and equipment against freeze damage.

If the outside air temperature sensor falls below

36° F, “Freeze Protection” is activated and the Filter Pump relay is switched on to circulate the pool

water. To enable freeze protection for a circuit, see “Settings Menu: Circuit Function, ” on page 39.

Mode button: Use this button for service purposes to manually control the EasyTouch system. Press

this button once activate “Service” mode, to allow AUX circuit buttons, Filter Pump, Valves, Heater

and Solar buttons to be operated manually. Press the button a second time to enable “Timeout”

mode. This mode is similar to “Service” mode except that the system will automatically return to

normal operation (Auto) after three hours. Press the button a third time to return the system to

“AUTO” mode. The current operating status is shown in the LCD display. The menu buttons,

remote controllers, and menu scheduled operations are disabled (except for switching off equipment

manually for emergencies) while the system is in “Service” mode.

Auto: In Auto (automatic) mode the system is in normal operating mode and is controlled by the

main control panel LCD menu features.

Service: Use this mode to service pool equipment and to operate equipment manually.

Timeout: Same functionality as “Service” mode, except that the system will automatically return to

normal operation (Auto) after three hours.

➃

➄

➅

➆

SELECT

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 87 88

Comments to this Manuals

No comments

Compool Cp3800 User's Guide Page 12

Comments to this Manuals

Related products and manuals for Above ground pool accessories Compool Cp3800