Compool Cp3800 User's Guide Page 2
- Page / 88
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
© 2010 Pentair Water Pool and Spa, Inc. All rights reserved.
1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 West Los Angeles Ave., Moorpark, CA 93021 • (800) 553-5000
EasyTouch®, Compool®, IntelliChlor®, IntelliFlo®, MagicStream®, ThermalFlo®, QuickTouch®, IntelliBrite®,
SAm®, SAL®, FIBER
works
®, Photon Generator®, and Pentair Water Pool and Spa® are trademarks and/or
registered trademarks of Pentair Water Pool and Spa, Inc. and/or its affiliated companies in the United States and/
or other countries. Unless noted, names and brands of others that may be used in this document are not used to
indicate an affiliation or endorsement between the proprietors of these names and brands and Pentair Water Pool
and Spa, Inc. Those names and brands may be the trademarks or registered trademarks of those parties or others.
P/N 521102 - Rev A - 02/04/2010
The Compool EasyTouch Upgrade circuit board is factory configured and ready to operate as a
SHARED EQUIPMENT system (Jumper J25 = ON). To change the Compool EasyTouch Upgrade board
to operate a SINGLE BODY system, first remove Jumper 25 (place the jumper on one of the pins) and
erase the EEPROM (see page 49).
To change Compool EasyTouch circuit board:
1. Write down your Compool system settings and connections (e.g. filter pump schedules,
auxiliary connection for lights, spa jets etc.).
2. Change system to SINGLE BODY system (jumper OFF): Remove circuit board Jumper
J25. Place the jumper on one of the pins. J25 is located in the upper/center of the circuit
board (see page 76).
3. Erase the circuit board EEPROM: Power up the Compool EasyTouch Upgrade circuit
board. To erase the EEPROM, press MENU > SETTINGS > Erase EEPROM and follow
the screen prompts as shown below:
Up/Down button: Select Yes.
Right button: The message “Erase EEPROM Are You Sure? No” is
displayed.
Up/Down button: Select Yes.
Right button: Press this button to erase system data and restore the
factory defaults. The display will go blank, then the main screen will be
displayed.
MENU ▼ SETTINGS ▼ Erase EEPROM Erase EEPROM
Getting There
▲
4. Continue to setup your system using the EasyTouch menu (see page 14).
Configuring Compool/EasyTouch as a SINGLE BODY SYSTEM
IMPORTANT INFORMATION
How to change your Compool/EasyTouch Upgrade
system to a “Single Body” system
Erase EEPROM
Erase ALL? No (Yes)
Erase EEPROM
Are You Sure?
No (Yes)
AUTO HEATER
SPA 95°F / 100°F
AIR 70°F
MON 09:30 AM
- Installation and User’s Guide 1
- IMPORTANT INFORMATION 2
- Contents 3
- Contents (Continued) 4
- Technical Support 8
- Accessory Equipment 8
- Section 1 9
- Overview 9
- SPA 95 F / 100 F 10
- AIR 70 F 10
- MON 09:30 AM 10
- AUTO HEATER 11
- SPA 95 F / 100 F 11
- QuickTouch 14
- POWER ON 15
- MENU HEAT 17
- Getting There 17
- MTWTFS 18
- Setting the Egg Timer Feature 20
- Section 2 21
- EasyTouch Menus 22
- (Continued) 23
- Main Screen 24
- Menu F. Circuits 25
- MENU LIGHTS LIGHTS 26
- Setting up lights (Continued) 29
- Continue on next page 31
- MENU ▼ DELAY CANCEL 34
- Settings Menu: Clock 39
- Settings Menu: IntelliFlo 40
- (or IntelliPro 40
- Settings Menu: IntelliChlor 43
- Settings Menu: ThermalFlo 44
- Heat Pump 44
- Circuit Names 45
- Circuit #: 3/18 45
- Circuit : AUX 1 45
- [AUX 1 ] 45
- EasyTouch Circuit Names 46
- Circuit/Fun 47
- [SPA ] 47
- [Master Spa ] 47
- Freeze: Yes/No 47
- Preset Circuit Functions 48
- Cstm Name 1/10 49
- [USERNAME-01] 49
- Set Valves 49
- A: [CLEANER ] 49
- B: [FOUNTAIN ] 49
- 2-Speed Pmp 1/4 50
- Circuit: 50
- [SPA HEATER ] 50
- Settings Menu: Delays 51
- Settings Menu: iSx Pump Cntrl 54
- ° F limit 55
- Assign QT4 55
- Circuit: 1/4 55
- [SPA ] 55
- Settings Menu: Calibration 56
- Set Password 57
- PW : [0000] 57
- Enable : No 57
- Address Wireless 58
- Sending Address 58
- <MENU> 58
- Scanning 58
- Spa Side [Off/On] 59
- Press Any Button 60
- Firmware Version 60
- Soft: 1.02 60
- Boot: 1.02 60
- Press Any Button 60
- Diagnostics Menu: Chlorinator 61
- Diagnostics Menu: Water Temp 61
- Diagnostics Menu: Solar Temp 61
- Diagnostics Menu: Air Temp 62
- Section 3 63
- Troubleshooting 63
- EasyTouch Error Messages 64
- System Problem Diagnosis 66
- First Time System Start-Up 69
- Synchronizing control panels 71
- Wiring Description 71
- Blank Page 72
- Section 4 73
- SPA 95 F / 1 00 F 77
- Wiring from 79
- WIRING DIAGRAM 84
- UPGRADE 84
- Low Voltage Wiring 85
- P/N 521102 Rev A 88
- *521102* 88
Related products and manuals for Above ground pool accessories Compool Cp3800
(22 pages)© 2020, manymanuals.com. All rights reserved. | 1.971 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals