Compool Cp3800 User's Guide download pdf (Page 52)

Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide

Settings Menu: F° / C° (Fahrenheit/Celsius)

The temperature settings for the water, solar and air can be displayed in either Fahrenheit or Celsius.

F° / C°

To change the temperature units:

Up/Down buttons: Select either Fahrenheit or Celsius. Press the Menu button to

save the settings and to return to the Settings menu options. Press the Menu button

again to return to the main menu options or press again to return to the main screen.

Settings Menu: iS4 Spa-Side Remote Controller

You can specify any iS4 Spa-Side remote button to control different functions by assigning each button to a

specific circuit. For example, you can use the iS4 Spa-Side remote to activate the spa circulation and for

operating auxiliary equipment such as heater, lights, jet pump, heat boost, air blower, waterfall, etc.). You can

also use the “Pump Incrs” and “Pump Decrs” circuit to increase or decrease the pump speed for an IntelliFlo

VF (GPM) or VS (RPM) pump. For example, if the “Pump Incrs” circuit is assigned to an iS4 button, each

press of the button will increase the pump speed in specific speed increments as specified in the “iSx Pump

Cntrl” menu setting (see page 46). Speed increments are set from 10 to 250 RPM (or 1 to 10 GPM, for the

IntelliFlo VF).

Assign iS4

Before configuring the iS4 Spa-Side remote controller assign names to the circuits (see page 42).

To assign iS4 Spa-Side buttons:

Up/Down buttons: Select a circuit to one of the iS4 buttons. You can set up to four

circuits (1/4, 2/4, 3/4, 4/4).

Right button: Select the circuit setting.

Up/Down buttons: To configure the first button on the iS4 Spa-Side Remote, scroll

through the circuit names and find the circuit that you would like to assign to the first

button on the iS4. The generic circuits selections are: None, Spa, Pool, Aux 1-7,

Feature 1-8, Solar (if selected in “Heat” menu), Heat Boost, Heat Enable, Pump

Incrs, Pump Decrs. “Aux Extra” is displayed only available if the Solar output (J17)

plug on the EasyTouch motherboard is not being used for solar equipment. Use the

Solar button to switch the extra circuit on and off (see page 5). Selecting “None”

does not assign a circuit.

Note: The “Heat Boost” feature will switch on the heater for seven minutes to

increase the spa water temperature. Each time the spa Heat Boost button is

pressed, the temperature will increase about 1

° F. The temperature will not go

beyond the 104° F limit.

Right button: Assign the next circuit (2/4).

Up/Down buttons: Select the first digit for the circuit number (1/4, 2/4, 3/4, 4/4) and

repeat the procedure for the other three buttons.

Press the Menu button to save the settings and to return to the Settings menu

options. Press the button again to return to the main menu options or press again to

return to the main screen.

MENU ▼ SETTINGS ▼ IS4 ASSIGN IS4

Getting There

▲



F° / C°

FAHRENHEIT



MENU ▼ SETTINGS ▼ F˚ / C˚ F˚ / C˚

Getting There

▲



Assign iS4

Circuit: 1/4

[HEAT BOOST ]



Note: To

disable or

enable the

iS4 Spa-Side

remote, see

Settings

Menu: Spa

Side,” on

page 51.

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 87 88

Comments to this Manuals

No comments

Compool Cp3800 User's Guide Page 52

Comments to this Manuals

Related products and manuals for Above ground pool accessories Compool Cp3800