Compool Cp3800 User's Guide download pdf (Page 30)

Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide

Setting up lights (Continued)

Config

From the “Config” screen you can setup the IntelliBrite light position, and specify the color of each pool and

spa light. Any combination of up to eight IntelliBrite lights, Pentair SAM, SAL and or Fiberworks lights can be

preset for specific colors and position when using the “Color Swim” and “Color Set” feature. Fixed light color

are selected and activated from the Colors screen. Note: The “Config” menu settings do not apply to the

MagicStream laminars.

To select configure a light position and color:

Menu > Lights > Config:

Up/Down buttons: Choose the light circuit (1-8) to configure. Select an available

auxiliary circuit (NONE). For more about assigning an auxiliary circuit to a light,

see “Circuit Functions (page 39) and “Circuit Names” (page 37). Up to eight (8)

auxiliary circuits.

Right button: Select the light to setup.

Up/Down buttons: Select the light circuit.

Right button: Select the light color selection.

Up/Down buttons: Select the light color (Blue, Cyan, Green, Lt. Green,

White, Lt. Magenta, Magenta, Lavender).

Right button: Select the light position selection.

Up/Down buttons: Select the light position. A light can be assigned to any

position from 1 through 12. To ensure that the “Color Swim” and “Color Set”

lighting feature color effects are correct, set the position of the light according to

where it’s located in the pool or spa. Position 1 will lead all the other lights in the

color changing sequence. Position 2 follows Position 1 and so on. There are 12

position to choose from. More than one light may be assigned to the same position

number so that their colors may be synchronized. For example, to make the colors

swim right to left, make your right most light Position 1. You may need to go

back to and scroll through your lights to find the right most light, and set it as

Position 1.

Right button: Select the light delay selection. The Delay time between two or

more lights can be set from 0 to 60 seconds. Use a higher delay time for lights

spread further apart. Try five seconds for all lights and observe the effect. Use

different time settings to achieve unique lighting moods and effects.

Press the Menu button to setup other lights or press Menu button four times

to return main screen.

Setting up SAM, SAL, PG2000, Color Wheel Lights

Before using the lighting feature “Color Swim” or “Color Set” with Pentair SAM or SAL lights, make sure the

AUX relay circuits which control the lights have been assigned as “light” circuit and that the name (AUX 1,

AUX 2) has been changed to best fit the light being used. Verify that SAm and/or SAL, and/or FIBERworks

have been assigned in “Circuit Functions” as SAM or SAL light. If FIBERworks lighting is incorporated, it

also has to be set up as a “PHOTON GENERATOR” light for the circuit controlling the light bulb, and

COLOR WHEEL for the circuit controlling the color wheel it self. The circuit light “functions” are: Light,

SAM, SAL, Photon Generator, Color Wheel, and IntelliBrite, see page 40 for a more information.

1- [POOL ]

2- [SPA ]

3- [BACK YARD ]

4- [AUX 4 ]





5- [NONE ]

6- [NONE ]

7- [NONE ]

8- [NONE ]





[ AUX 4 ]

[ LAVENDER ]

[ 1ST POSITION ]

[ DELAY 5 SECS ]

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 87 88

Comments to this Manuals

No comments

Compool Cp3800 User's Guide Page 30

Comments to this Manuals

Related products and manuals for Above ground pool accessories Compool Cp3800